FITTING NEW REAR SHOCKERS
(IF FITTING REAR SPRINGS AT THE SAME TIME PLEASE LOOK OUT FOR THE REAR SPRING + SHOCK GUIDE)
FITTING PRO-COMP ES9000`S TO K reg LWB PAJERO
TOOLS NEEDED:
BIG JACK
AXLE STANDS
BIG CRACK BAR
SPANNERS: 8mm, 2x17mm, 24mm OR BIG ADJUSTABLE
SOCKETS: 17mm, 24mm
WIRE BRUSH
MOLE GRIPS
LOTS OF STRONG TIEWRAPS
HAMMER
CHISEL
CRAFT KNIFE
LOTS OF WD40
SPRAY THE TOP AND BOTTOM SHOCKER MOUNTINGS TWICE A DAY WITH LOTS OF WD40 FOR A FEW DAYS BEFORE YOU DO THIS
DO BOTH SIDES AT ONCE: CRACK OFF THE WHEEL NUTS, JACK THE CAR UP FROM UNDER THE REAR DIFF AND SUPPORT WITH AXLE STANDS ON THE CHASSIS RAILS . REMOVE THE WHEELS.
IF YOU HAVE THE ACTUATORS FITTED FOR THE ADJUSTABLE SUSPENSION YOU NEED TO REMOVE THESE NEXT. I WHACKED MOST OF MINE OFF WITH THE HAMMER AND CHISEL BECAUSE THE ES9000`S DONT USE THEM AND I`M NEVER GOING TO RE-FIT STANDARD SHOCKERS. YOU CAN REMOVE THEM WITH THE 8mm SPANNER, BUT THE BOLT WILL PROBABLY SNAP ANYWAY.
USE A THIN 17mm SPANNER (THE ONE OUT OF THE BOOT TOOLKIT IS FINE) TO HOLD THE LOWER OF THE 2 NUTS ON THE TOP MOUNTING, AND USE ANOTHER 17mm SPANNER ON THE TOP NUT, GOOD LUCK, ITS HARD WORK, I HAD TO CUT ONE OF MINE OFF WITH THE ANGLE GRINDER.
REMOVE THE REST OF THE ACTUATOR BRACKET, THE LOWER NUT, (MIGHT NEED TO HOLD THE TOP OF THE THREADS WITH THE MOLE GRIPS IF IF SPINS),
THE WASHER WITH THE PIN ON IT AND THE RUBBER BUSH.
REMOVE THE BOTTOM MOUNTING USING THE 24mm SOCKET ON THE BIG BAR AND THE BIG ADJUSTABLE/24mm SPANNER ON THE OTHER END. THIS ONE WILL BE QUITE TIGHT TOO.
REMOVE THE BOTTOM BOLT, COMPRESS THE SHOCKER AND REMOVE..
****************************************************************************************************************************************************************************************
I`VE HAD TO MAKE SOME OF THE REST UP COS I HAVENT GOT THE ES9000`S, THEY WERE OUT OF STOCK, SO I`VE PUT ES3000`S ON AND THEY AREN`T NITROGEN FILLED SO WERE EASIER TO COMPRESS AND I DIDN`T HAVE TO MESS ABOUT WITH THE TIEWRAPS, BUT I`VE LEFT THIS PART IN INCASE THE ES9000`S ARE MORE DIFFICULT....
THE OLD ONE CAME OUT QUITE EASILY, BUT THE ES9000`S ARE NITROGEN FILLED AND WHILE IT IS POSSIBLE TO COMPRESS THEM, THEY EXTEND AS SOON AS YOU TAKE PRESSURE OFF MAKING THEM HARD TO FIT. WHAT I DID WAS MAKE 2 LOOPS OF TIEWRAPS GOING THRO THE BOTTOM BUSH AND ONTO THE WELDED TOP CAP, WITH ANOTHER TIEWRAP HOLDING THEM IN PLACE... THIS MEANT I COULD COMPRESS THEM THEN PULL THE TIEWRAPS TIGHT TO HOLD THEM IN PLACE....MAKE SURE YOU FIT THE BOOT BEFORE YOU DO THIS....AND THE STICKER IF YOU WANT IT ON..... ***SEE PHOTO***
FIT THE LOWER WASHER AND BUSH ON THE TOP MOUNTING
FIT THE METAL SLEEVE IN THE BOTTOM MOUNTING BUSH, CHOOSE WHICH ONE GIVES THE SNUGGEST FIT AROUND YOUR BOTTOM BOLT.
WIGGLE THE SHOCKER THRO` THE HOLE AND INTO THE BOTTOM MOUNTING. THE TOP MIGHT NEED LEVERING IN DEPENDING ON HOW MUCH YOU MANAGED TO GET IT COMPRESSED.
SNIP THE TIEWRAPS, WIGGLE THE TOP MOUNT AROUND TO SEAT THE BUSH AND FIT THE TOP BUSH, WASHER AND NUT.... ( I COULDN`T GET ENOUGH THREADS SHOWING TO GET THE NUT ON SO I TRIMMED OFF SOME OF THE BUSH FROM ONE SIDE WITH THE CRAFT KNIFE)
REMOVE THE REST OF THE TIEWRAPS FROM THE HOLE & REFIT THE BOTTOM MOUNTING BOLT, WASHERS AND NUT, AND RETORQUE TO:
LEAF SPRING MODELS:
REAR SHOCKER NUTS: 22nm
COIL SPRING MODELS:
UPPER SHOCK ABSORBER NUT: 15nm
LOWER SHOCK ABSORBER BOLTS: UPTO + INC 1993: 120nm
LOWER SHOCK ABSORBER BOLTS: 1994 ON: 216nm
SECURE THE BOTTOM OF THE (RED) BOOT WITH THE SUPPLIED TIEWRAP
REPLACE THE WHEELS, LOWER TO THE GROUND AND RETORQUE THE WHEEL NUTS
THIS GUIDE IS EXACTLY THAT....... A GUIDE. THIS IS MY EXPERIENCE AND MAYBE IT WILL BE OF SOME HELP TO YOU. I AM NOT A PROFESSIONAL MECHANIC, AND I ACCEPT NO RESPONSIBILITY FOR ANYTHING EVER. ALWAYS SUPPORT THE CAR ON AXLE STANDS CAPABLE OF TAKING THE WEIGHT, AND ALWAYS USE PROTECTIVE CLOTHING: ie GOGGLES IF YOU DONT WANT RUST IN YOUR EYES, A COAT IF ITS RAINING......... IF YOU`RE NOT SURE WHAT YOUR DOING - DON`T DO IT, GET A PROFESSIONAL TO DO IT
OTHER WISE "GOOD LUCK"
NOT MANY PHOTOS, BUT I`LL ADD MORE WHEN I FIT THE ES9000`S
Pajero UK
Author
DSCF0001-1 (Small)2.JPG
Logged
